Silex technology Embedded Intelligent Module SX-560 Manuel d'utilisateur Page 2

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 1
1 RESETI- 2 GPIO_0
3 GPIO_1 4 GPIO_2
5 GROUND 6 +3.3VDC
7 GPIO_3 8 GPIO_4
9 GPIO_5 10 GPIO_6
11 GPIO_7 12 GPIO_8
13 GPIO_9 14 TXD0
15 GPIO_10 16 CTS0-
17 GROUND 18 +3.3VDC
19 USB+ 20 RTS0-
21 USB- 22 RXD0
23 +3.3VDC 24 GROUND
25 SPI_CS- 26 TXD1
27 SPI_CLK 28 CTS1-
29 GROUND 30 +3.3VDC
31 SPI_MOSI 32 RTS1-
33 SPI_MISO 34 RXD1
35 +3.3VDC 36 GROUND
37 IIC_SDC 38 TXD2
39 IIC_SDA 40 RXD2
OEM Module Diagram
OEM Interface
Pin Signal Pin Signal
Specifications
Wireless Interface
802.11a/b/g (54Mbps/11Mbps)
Serial Ports
2 x UART with TXD, RXD, RTS, CTS
and up to 921.6Kbps per port; 3
GPIOs are configurable as DTR,
DSR, and DCD on port 1
USB Port
USB V1.1 host (12Mbps)
SPI Port
25MHz; compatible with 2-ch
Serial Peripheral Interface
Protocol V2.11; Master-Slave,
Slave-Master, and Master-Master
modes of operation
Console Port
A dedicated UART console port is
available for configuration
General Pupose I/O Signals
9 general purpose signals are
accessible via the OEM header
(external pull-ups are required
for customization)
Power
Power Consumption (3.3V±10%; no
load on I/O ports or GPIOs)
Maximum: 350mA Average: 238mA
Minimum: 73mA (connected
to access point in powersave
mode; SX-560 will wake up
upon data received in UART
or other interrupt)
Environmental
Temperature
Operating Temperature: 0
º
to
+55
º
C (commercial version); -20
º
to +80
º
C (extended temp version)
Storage Temperature: -40
º
to
+85
º
C
Ma
x
imum temperature change
per hour: 20
º
C
Relative Humidity
Operating: 20% to 80% non-
condensing
Storage: 10% to 90% non-
condensing
Altit de
Operating 3.1km
Storage 9km
Standards Compliance
FCC (Part 15 Subpart C) and IC
modular certification; RS-232
232, IEEE 802.11a/b/g, RFC 2217,
RoHS; designed for compliance
with FCC, CE, VCCI Class B, and
EN60601 EMC standards, and CE
and TELEC wireless standards
The OEM interface allows OEMs to add functionality via a
daghtercard. Power is also input through this interface. This is a 40-
pin 0.5-mm pitch surface-mount header (Hirose DF12-40DS-0.5V or
equivalent). Pin assignments are shown below.
Idle: 198 mA Sleep: 73mA
u
Vue de la page 1
1 2

Commentaires sur ces manuels

Pas de commentaire